Question Adding IPv6 to plesk server without issues

[Servus]

Since several user have the same problem adding IPv6 to plesk server wihich breaks configuration after next reboot I was happy to find a new Plesk IPv6 adding support article.
Problem & question:
Is it also possible on 1and1 server with Ubuntu 16.04 and Plesk Onyx?
Reason for asking is that my /etc/sysctl.conf is existing but after half an year usage in production every line in sysctl.conf is commented out by #. Not one line related to Ipv4 or Ipv6 seems to be used directly for configuration. Might be possible that no definition is needed. Perhaps another .conf file is used for the system in the end I posted /etc/conf.d/10-ipv6-privacy.conf. (but only 2 lines).
If I would add the two recommended lines for IPv6, then they would be the only ones uncommented.

#
# /etc/sysctl.conf - Configuration file for setting system variables
# See /etc/sysctl.d/ for additional system variables.
# See sysctl.conf (5) for information.
#

#kernel.domainname = example.com

# Uncomment the following to stop low-level messages on console
#kernel.printk = 3 4 1 3

##############################################################3
# Functions previously found in netbase
#

# Uncomment the next two lines to enable Spoof protection (reverse-path filter)
# Turn on Source Address Verification in all interfaces to
# prevent some spoofing attacks
#net.ipv4.conf.default.rp_filter=1
#net.ipv4.conf.all.rp_filter=1

# Uncomment the next line to enable TCP/IP SYN cookies
# See http://lwn.net/Articles/277146/
# Note: This may impact IPv6 TCP sessions too
#net.ipv4.tcp_syncookies=1

# Uncomment the next line to enable packet forwarding for IPv4
#net.ipv4.ip_forward=1

# Uncomment the next line to enable packet forwarding for IPv6
#  Enabling this option disables Stateless Address Autoconfiguration
#  based on Router Advertisements for this host
#net.ipv6.conf.all.forwarding=1


###################################################################
# Additional settings - these settings can improve the network
# security of the host and prevent against some network attacks
# including spoofing attacks and man in the middle attacks through
# redirection. Some network environments, however, require that these
# settings are disabled so review and enable them as needed.
#
# Do not accept ICMP redirects (prevent MITM attacks)
#net.ipv4.conf.all.accept_redirects = 0
#net.ipv6.conf.all.accept_redirects = 0
# _or_
# Accept ICMP redirects only for gateways listed in our default
# gateway list (enabled by default)
# net.ipv4.conf.all.secure_redirects = 1
#
# Do not send ICMP redirects (we are not a router)
#net.ipv4.conf.all.send_redirects = 0
#
# Do not accept IP source route packets (we are not a router)
#net.ipv4.conf.all.accept_source_route = 0
#net.ipv6.conf.all.accept_source_route = 0
#
# Log Martian Packets
#net.ipv4.conf.all.log_martians = 1
#

/etc/sysctl.d/10-ipv6-privacy.conf

# IPv6 Privacy Extensions (RFC 4941)
# ---
# IPv6 typically uses a device's MAC address when choosing an IPv6 address
# to use in autoconfiguration. Privacy extensions allow using a randomly
# generated IPv6 address, which increases privacy.
#
# Acceptable values:
#    0 - don’t use privacy extensions.
#    1 - generate privacy addresses
#    2 - prefer privacy addresses and use them over the normal addresses.
net.ipv6.conf.all.use_tempaddr = 2
net.ipv6.conf.default.use_tempaddr = 2

kindest regards